JND Reproducible Thermodynamic Modelling and Energy-Normalized Assessment of a Small-Scale Plastic Pyrolysis Reactor for PE, PP, and HDPE Waste
Mechanical Engineering
DOI:
Abstract
Pyrolysis offers a promising route for recovering liquid hydrocarbons from difficult-to-recycle polyolefin waste; however, small-scale reactor studies can provide incomplete assessment when reported oil production is not considered together with the thermal energy required to heat the feedstock, reactor hardware, and compensate for heat losses. This study develops a transparent and reproducible thermodynamic framework for a small-scale pyrolysis reactor processing polyethylene (PE), polypropylene (PP), and high-density polyethylene (HDPE). The model was formulated using direct mass- and energy-balance equations based on the reported fabricated reactor geometry, a 3 kg batch basis, literature-derived thermophysical properties, polymer fusion and pyrolysis enthalpies, reactor-wall heating, and heat-loss calculations. A deterministic MATLAB implementation was used to evaluate thermal input over 400–550 °C and to assess the sensitivity to insulation thickness from 10 to 50 mm. Model outputs were assessed against the reported final plastic-waste-oil (PWO) volumes, while experimental observations, literature-derived properties, modelling assumptions, and legacy numerical results were kept explicitly separated. At 500 °C, the calculated thermal inputs were 10.67 MJ for PE, 10.88 MJ for PP, and 14.00 MJ for HDPE. Increasing the assumed insulation thickness from 10 to 50 mm reduced the calculated thermal input by approximately 9.3–12.0%. The reported PWO volumes were 1.50 L for PE, 1.40 L for HDPE, and 0.90 L for PP. Under a common 500 °C reference condition, the corresponding reference energy-normalized oil-recovery indices (REORI) were 0.141, 0.100, and 0.083 L MJ⁻¹, respectively. REORI provides a common-basis comparative screening indicator by relating reported PWO volume to modelled thermal input, but it should not be interpreted as measured process efficiency. The framework demonstrates the importance of considering reactor thermal mass and heat-loss control alongside feedstock properties when assessing small-scale pyrolysis systems. However, the analysis is limited by the unavailability of direct heater-energy measurements, calibrated reaction-zone temperature data, cooling-water flow records, replicate measurements, and complete primary experimental records. Future work should therefore incorporate direct heater-power or energy-consumption measurements, calibrated reaction-zone temperature monitoring, oil mass-yield determination, condenser heat-removal measurements, and replicated experiments to enable rigorous energy-efficiency evaluation and validation of the thermodynamic framework.
Downloads
Views : 62
Downloads : 48
References
M. S. Qureshi et al., “Pyrolysis of plastic waste: Opportunities and challenges,” J. Anal. Appl. Pyrolysis, vol. 152, Art. no. 104804, Nov. 2020. doi: 10.1016/j.jaap.2020.104804.
S. H. Chang, “Plastic waste as pyrolysis feedstock for plastic oil production: A review,” Sci. Total Environ., vol. 877, Art. no. 162719, Jun. 2023. doi: 10.1016/j.scitotenv.2023.162719.
M. H. Rahman, P. R. Bhoi, and P. L. Menezes, “Pyrolysis of waste plastics into fuels and chemicals: A review,” Renew. Sustain. Energy Rev., vol. 188, Art. no. 113799, Dec. 2023. doi: 10.1016/j.rser.2023.113799.
L. Fulgencio-Medrano, S. Garcia-Fernandez, A. Asueta, A. Lopez-Urionabarrenechea, B. B. Perez-Martinez, and J. M. Arandes, “Oil production by pyrolysis of real plastic waste,” Polymers, vol. 14, no. 3, Art. no. 553, Feb. 2022. doi: 10.3390/polym14030553.
S. Kartik et al., “Valorization of plastic wastes for production of fuels and value-added chemicals through pyrolysis – A review,” Therm. Sci. Eng. Prog., vol. 32, Art. no. 101316, Sep. 2022. doi: 10.1016/j.tsep.2022.101316.
S. D. A. Sharuddin, F. Abnisa, W. M. A. W. Daud, and M. K. Aroua, “A review on pyrolysis of plastic wastes,” Energy Convers. Manag., vol. 115, pp. 308–326, May 2016. doi: 10.1016/j.enconman.2016.02.037.
M. M. Hasan, R. Haque, M. I. Jahirul, and M. G. Rasul, “Pyrolysis of plastic waste for sustainable energy recovery: Technological advancements and environmental impacts,” Energy Convers. Manag., vol. 326, Art. no. 119511, Feb. 2025. doi: 10.1016/j.enconman.2025.119511.
S. Ning Li, H. Liu, Z. Cheng, B. Yan, and G. Chen, “Conversion of plastic waste into fuels: A critical review,” J. Hazard. Mater., vol. 424, Art. no. 127460, Feb. 2022. doi: 10.1016/j.jhazmat.2021.127460.
A. K. Burnham, “Insight into Polyethylene and Polypropylene Pyrolysis: Global and Mechanistic Models,” Energy Fuels, vol. 35, no. 8, pp. 6480–6503, Apr. 2021. doi: 10.1021/acs.energyfuels.1c00342.
G. K. Parku, F.-X. Collard, and J. F. Görgens, “Pyrolysis of waste polypropylene plastics for energy recovery: Influence of heating rate and vacuum conditions on composition of fuel product,” Fuel Process. Technol., vol. 209, Art. no. 106522, Nov. 2020. doi: 10.1016/j.fuproc.2020.106522.
A. A. Darko, M. Thulficar, and K. J. Whitty, “Pyrolysis of plastics in a multi-zone reactor: System performance and characterization of oil, gas and char,” Energy Convers. Manag., vol. 353, Art. no. 121192, Mar. 2026. doi: 10.1016/j.enconman.2026.121192.
Y. Li, W. Wang, F. Yin, and K. Wang, “Threshold temperature pyrolysis of waste plastic and the effect on pyrolysis energy consumption and product distribution,” Therm. Sci. Eng. Prog., vol. 67, Art. no. 104105, Feb. 2025. doi: 10.1016/j.tsep.2025.104105.
M. Laghezza, S. Fiore, and F. Berruti, “A review on the pyrolytic conversion of plastic waste into fuels and chemicals,” J. Anal. Appl. Pyrolysis, vol. 179, Art. no. 106479, May 2025. doi: 10.1016/j.jaap.2024.106479.
B. Muharto, F. R. Saputro, W. Prabowo, and T. Anggoro, “Pyrolysis process control: Temperature control design and application for optimum process operation,” Int. J. Electr. Comput. Eng., vol. 14, no. 2, pp. 1473–1485, Apr. 2024. doi: 10.11591/ijece.v14i2.pp1473-1485.
J. Esteban et al., “Microstructural Analysis and Mechanical Behavior of Mg–Zn–Y Alloys with LPSO Phases Processed by Cryo-Rolling,” Metallogr. Microstruct. Anal., vol. 14, pp. 1120–1132, Feb. 2025. doi: 10.1007/s13632-025-01231-0.
K. P. Dinda, “Advances in plastic to fuel conversion: Reactor design, operational optimization, and machine learning integration,” Sustain. Energy Fuels, vol. 9, no. 1, pp. 54–71, Jan. 2025. doi: 10.1039/d4se01045k.
M. Jeremiah and B. Kabeyi, “Review and Design Overview of Plastic Waste-to-Pyrolysis Oil Conversion with Implications on the Energy Transition,” Adv. Mater. Sci. Eng., vol. 2023, Art. no. 1821129, May 2023. doi: 10.1155/2023/1821129.
A. Antelava et al., “Energy Potential of Plastic Waste Valorization: A Short Comparative Assessment of Pyrolysis versus Gasification,” Energy Fuels, vol. 35, no. 5, pp. 3600–3613, Mar. 2021. doi: 10.1021/acs.energyfuels.0c04017.
T. Maqsood, J. Dai, Y. Zhang, M. Guang, and B. Li, “Pyrolysis of plastic species: A review of resources and products,” J. Anal. Appl. Pyrolysis, vol. 159, Art. no. 105295, Oct. 2021. doi: 10.1016/j.jaap.2021.105295.
L. Dai et al., “Pyrolysis technology for plastic waste recycling: A state-of-the-art review,” Prog. Energy Combust. Sci., vol. 93, Art. no. 101021, Nov. 2022. doi: 10.1016/j.pecs.2022.101021.
O. Y. Yansaneh and S. H. Zein, “Recent Advances on Waste Plastic Thermal Pyrolysis: A Review,” Processes, vol. 10, no. 2, Art. no. 332, Feb. 2022. doi: 10.3390/pr10020332.
D. V. Suriapparao and R. Tejasvi, “A review on role of process parameters on pyrolysis of biomass and plastics: Present scope and future opportunities in conventional and microwave-assisted pyrolysis technologies,” Process Saf. Environ. Prot., vol. 162, pp. 435–462, Jun. 2022. doi: 10.1016/j.psep.2022.04.024.
Y. Zhao et al., “Kinetics, Product Evolution, and Mechanism for the Pyrolysis of Typical Plastic Waste,” ACS Sustain. Chem. Eng., vol. 10, no. 1, pp. 91–103, Jan. 2022. doi: 10.1021/acssuschemeng.1c04915.
Y. Ayub and J. Ren, “Revealing the synergistic effect of feedstock compositions and process parameters in co-pyrolysis: A review based on bibliometric analysis and experimental studies,” J. Clean. Prod., vol. 459, Art. no. 142540, Jul. 2024. doi: 10.1016/j.jclepro.2024.142540.
S. Garg et al., “A novel investigation using thermal modeling and optimization of waste pyrolysis reactor using finite element analysis and response surface methodology,” Sci. Rep., vol. 13, Art. no. 10931, Jul. 2023. doi: 10.1038/s41598-023-37793-8.
M. Hedayati Marzbali et al., “Design of a 1-D auger reactor for upcycling polystyrene to styrene via pyrolysis,” Chemosphere, vol. 378, Art. no. 144368, Jun. 2025. doi: 10.1016/j.chemosphere.2025.144368.
C. Qi, J. Wang, and V. Yadama, “Heat transfer modeling of oriented sorghum fibers reinforced high-density polyethylene film composites during hot-pressing,” Polymers, vol. 13, no. 21, Art. no. 3631, Nov. 2021. doi: 10.3390/polym13213631.
A. Ali et al., “Thermal and kinetic modeling of waste plastic pyrolysis process to enhance the process scalability: A state-of-the-art review,” J. Anal. Appl. Pyrolysis, vol. 195, Art. no. 107675, May 2026. doi: 10.1016/j.jaap.2026.107675.
B. Abbasgholi-Na et al., “Thermal diffusivity and conductivity of polyolefins by thermal lens technique,” Polymers, vol. 14, no. 13, Art. no. 2707, Jul. 2022. doi: 10.3390/polym14132707.
J. Langwieser et al., “Determination of the influence of multiple closed recycling loops on the property profile of different polyolefins,” Polymers, vol. 14, no. 12, Art. no. 2429, Jun. 2022. doi: 10.3390/polym14122429.
G. Li et al., “Uncovering strategies for quantifying thermo-kinetics, reaction heat, and synergistic rates of heat transfer-degradation in the chemical upcycling of polyolefins,” Energy, vol. 330, Art. no. 136798, Sep. 2025. doi: 10.1016/j.energy.2025.136798.
S. Khedri and S. Elyasi, “Determination of the heat of pyrolysis of HDPE via isothermal differential scanning calorimetry,” J. Therm. Anal. Calorim., vol. 131, no. 2, pp. 1509–1515, Feb. 2018. doi: 10.1007/s10973-017-6681-x.
M. Mustafa and S. E. Mushtaq, “Approximate analytic solutions of transient nonlinear heat conduction with temperature-dependent thermal diffusivity,” Abstr. Appl. Anal., vol. 2014, Art. no. 423421, 2014. doi: 10.1155/2014/423421.
S. A. Marzouk, M. M. Abou Al-Sood, E. M. S. El-Said et al., “Comprehensive review of heat transfer enhancement through constructal theory,” J. Therm. Anal. Calorim., vol. 150, pp. 18089–18127, 2025. doi: 10.1007/s10973-025-14630-w.
K. Kuhlmann, F. Möller, C. Sinn, I. Bösing, and J. Thöming, “Heat transport regimes in structured reactors: CFD analysis and influence of reactor diameter and length,” Results Eng., vol. 24, Art. no. 103282, Dec. 2024. doi: 10.1016/j.rineng.2024.103282.
B. L. Salvi, T. Soni, S. Jindal et al., “Design improvement and experimental study on shell and tube condenser for bio-oil recovery from fast pyrolysis of wheat straw biomass,” SN Appl. Sci., vol. 3, Art. no. 173, 2021. doi: 10.1007/s42452-021-04165-8.
P. Talwar, M. Alzate Agudelo, and S. Nanda, “Pyrolysis Process, Reactors, Products, and Applications: A Review,” Energies, vol. 18, no. 11, Art. no. 2979, Jun. 2025. doi: 10.3390/en18112979.
O. Bongomin, C. Nzila, J. I. Mwasiagi, and O. Maube, “Comprehensive thermal properties, kinetic, and thermodynamic analyses of biomass wastes pyrolysis via TGA and Coats-Redfern methodologies,” Energy Convers. Manag. X, vol. 24, Art. no. 100723, Oct. 2024. doi: 10.1016/j.ecmx.2024.100723.
